The KIT_AURIX_TC277_TRB is a versatile tool, providing quick access to the capabilities of TriCore's powerful architecture. Applications can be developed easily. The Evaluation Board is equipped with a variety of memories and peripherals for connection to the environment. There is also an interface for the On Chip Debugging Features (OCDS1 and DAP). The kit also includes several sets of development tools, which are stored on the included Evaluation Board CD-ROM. The Evaluation Board allows easily the development of TriCore applications with the corresponding tools.MCU Derivates: TC27xTCPU Clock: 200 MHzIncluding:- Evaluation Board (TriBoard)- USB cable- Power Supply- Extension Board- Free TriCore Entry Tool Chain- Getting Started, first 3 Steps to- Install the Tools- Set up your Hardware- Write and debug your first ProgramOn Board Interfaces:– Standard power connector- Micro USB connector for ASC Interface (ASC0) and miniWiggler- RJ45 connector for Ethernet- 16-pin header for JTAG interface (OCDS)- 10-pin header for DAP- 10pin (2x5) Header for LIN Transceiver (LIN)- 2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1)- 2 x 10pin (2x5) Header for FlexRay (ERAY-A and ERAY-B)- Four 80-pin connectors (male) + four 80-pin connectors (female) with all I/O signals- Optional ETK connector- Optional 10pin (2x5) Socket for HSCT- Aurora connector (only with Emulation Device) Summary of Features

• Infineon’s TC2X7 (e.g. TC277, TC267, TC2D7) Controller in LFBGA-292 Package
• FlexRay Transceivers
• Safety device (optional)
• High Speed CAN Transceivers
• USB to UART bridge
• Ethernet Gigabit PHY(dependant of assembled Controller)
• Serial Eeprom
• LIN Transceiver
• Crystal 20MHz (default) or External Clock
• USB miniWiggler JDS for easy debugging
• 8 Low Power Status LEDs
• 8-DIP switches for configuration
• access to all pins of controller
• 100mm x 160mm (EURO-Board)
• optional power supply via USB
• Connectors :
• The TC2X4 TriBoard offers a wide variety of connectors
• Standard power connector
• Micro USB connector for ASC Interface (ASC0) and miniWiggler
• RJ45 connector for Ethernet
• 16-pin header for JTAG interface (OCDS)
• 10-pin header for DAP
• 10pin (2x5) Header for LIN Transceiver (LIN)
• 2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1)
• 2 x 10pin (2x5) Header for FlexRay (ERAY-A and ERAY-B)
• four 80-pin connectors (male) + four 80-pin connectors (female) with all I/O signals
• optional ETK connector
• Components:
• Infineon’s Next generation micro controller supply TLE 7368-3E
• Three LEDs to validate power supply (5Volt / 3,3 Volt / 1,3 Volt)
• LED indicating /HDRST (ESR0) active state
• LED indicating activ miniWiggler JDS
• LED switched via DAS software
• 2x Infineon’s FlexRay Transceiver TJA1080A (NXP)
• 2x Infineon’s High Speed CAN-Transceiver TLE6250G
• Infineon’s LIN-Transceiver TLE 7259-2GE
• Infineon’s Safety Device SAK-CIC61508 (optional)
• USB to UART bridge FT2232HL (FTDI)
• Single Port Gigabit Ethernet PHY PEF7071 (LANTIQ)
• SPI eeprom (Atmel)
• 8 general purpose LEDs
• Reset switch
• 4-pin Dip switch

Target Applications

• Domain Control
• Advanced Drive Assistent Systems
• High end ESC
• Sensor fusion
• Engine Management Systems
• Transmission Control Units
• Inverter
• Battery Management Systems